Blog

What does CSA stand for in cables?

VW-1: These cables have passed a VW-1 flame test and carry a “fire resistant” designation. The VW-1 test provides an assessment of the cable insulation material and resilience to fire. This is one of the most severe tests since it's performed vertically and can be viewed as a worst-case test condition.

VW-1: The VW-1 rating written on a cable specifies the flammability of the outer jacket. It is a standardized test to measure how the outer jacket responds when exposed to a flame in a vertical orientation hence the abbreviation VW (vertical wire). VW-1 will be found on the jacket of the cable if it has a VW-1 rating.

What is UL wire rating?

UL Listed means the product has been tested and meets the laboratory's standard to be used by itself for a specific purpose. UL Classified products have been evaluated only for specific properties, a limited range of hazards, or suitability for use under limited conditions.Oct 24, 2019

What is CL2 cable?

CL2: This is a cable jacket fire resistance rating defined in Article 725 of the National Electric Code. It stands for "Class 2 Remote-Control, Signaling, and Power-Limited Circuits" cable, which indicates that the cable is suitable for in-wall installation and use for certain low-voltage applications.

What is AWM number?

AWM is an acronym for Appliance Wiring Material. AWM conductors are UL recognized component wires evaluated for specific uses. Each style number has a specific use. ... The style number is optionally printed on the surface of the wire.Jan 16, 2008

What does AWM stand for on wire?

Appliance Wiring Material (AWM) Testing and Certification | UL.

image-What does CSA stand for in cables?
image-What does CSA stand for in cables?
Related

What does VW 1 mean on wire?

VW-1: These cables have passed a VW-1 flame test and carry a “fire resistant” designation. The VW-1 test provides an assessment of the cable insulation material and resilience to fire. This is one of the most severe tests since it's performed vertically and can be viewed as a worst-case test condition.

Related

Is CL3 better than CL2?

The difference between the two is that CL2 is rated for up to 150 volts while CL3 is rated for up to 300 volts. (NEC 725.71 F) According to NEC 725.2, CL2 offers some protection from electric shock while CL3 offers a bit more because it is rated to carry more voltage.

Related

What HDMI do I need for 4K?

HDMI 1.4 – If you want your HDMI cables to support 4K resolution, you need to make sure that they are High-Speed HDMI cables. They are tested to transmit video resolutions from 1080p to 4K with a richer color palette. With or without HDR, you need High-Speed HDMI cables.

Related

What does UL AWM mean?

Introduction. Appliance wiring material (AWM) is a large category of wire and cable that spans over different constructions. Underwriters Laboratory (UL) categorizes AWM as a Recognized Component used in Listed or Classified products.

Related

What is 1015 wire?

What is UL1015 Wire? UL 1015 hook-up wire is a PVC hook-up wire which is an Appliance Wiring Material (AWM) style that is based on the requirements of UL Standard 758, Appliance Wiring Materials. AWM 1015 is a general style for a single conductor wire that has an 80, 90 or 105°C temperature rating.

Related

What is AWM wire made of?

Appliance Wiring Material (AWM) consists of stranded, soft annealed copper conductors insulated with Polyvinylchloride (PVC). Constructions may be solid or stranded and are available in 1000 V (1kV) ratings. Canadian Standards Association (CSA) listed AWM-IA (Class I Group A) and TEW products are 600 V FT-1 rated.

Related

What is AWG in wire size?

AWG or American Wire Gauge is the US standard measure for the diameter of electrical conductors. The American Wire Gauge chart is based on the number of dies originally required to draw the copper down to the required dimensional size. It means the higher the AWG number is, the smaller the wire diameter is.

Related

What UL 1581?

UL 1581 is the Reference Standard for electrical wires, cables, and flexible cords operating in environments between 90°C and 105°C. This is the most widely used standard in North America for wire and cable, especially for temperature and FR ratings.

Share this Post: